Refuse Compactor Truck

1.The product function is introduced as follows

(1)It can actually hang 240 liters or 600 liters of garbage cans according to the user needs. Do a car can hang multiple garbage cans, this car fully meets the environmental requirements of the new concept of the garbage collection facilities, it can completely solve the secondary pollution problem of the garbage, to ensure the garbage filling evenly, so the garbage load is larger, reduce the number of transportation times, reduce the transportation cost. Energy-saving and environmental protection to improve efficiency!

(2)Base plate configuration: the new standard national six model, Weichai engine, 160 horsepower, 6-gear gearbox, 3900 wheelbase, 245 vacuum tire, air brake, original car air conditioning, yellow card procedures, the company provides all the vehicle registration procedures, the box color is optional.

(3)Upper configuration: the compressed garbage truck consists of sealed garbage box, sewage tank, hydraulic back cover, hydraulic system and operating system. The vehicle is fully sealed self-compression, self-dumping, compression in the process of sewage into the sewage box. The rear bucket turning mechanism or garbage bucket flipping mechanism can be selected, which completely solves the problem of secondary pollution in the process of garbage transportation. The imported parts have the advantages of high pressure, good sealing, easy operation, safety and so on.

2.The picture of the vehicle is as follows

3.Detailed parameters of the vehicle are as follows

4.The top decomposition picture display

5. Product use precautions

(1)Rotate the operation knob of the push board to the right push position, the push board in the box shall push the garbage out of the box and release the knob to complete the garbage discharge; (pay attention to the maintenance of the cylinder, and butter), find large pieces of other garbage (non-domestic garbage), stop the operation in time, continue the operation after removal, to avoid damage to the working device of the vehicle, strictly compress the construction waste,

(2)After a period of use, the car should check whether the universal joint screw is loose and needs to be tightened or replaced (the hydraulic pump and the drive shaft is not within the chassis service range because of the upper part, so the user needs to check and tighten regularly).

(3)For compressed garbage truck; before loading garbage, when the no-load operation reaches 6 air pressure standards, hang the force collector (the lower left of the steering wheel in the cab), check for leakage or abnormality, and then operate according to the indicated position of the operation knob plate;

(4)Garbage should be evenly put into the hopper, not concentrated on one side, so that the center of gravity of the vehicle is offset, or in the packing mouth along the high impact pressure filling garbage and garbage evenly distributed in the dustbin. When unloading and falling the piller, we should confirm the safety around and operate it carefully. Do not lift the piller on the slope, otherwise it is easy to move the center of gravity back and cause the rollover accident.

(5)The filler shall not enter normal driving until left and locked.

(6)The operation should avoid irrelevant personnel approaching the vehicle, especially the rear of the vehicle.

6. The picture of common accessories is as follows

7.The product after-sale service should know as follows

(1)Step 1.Turn the bucket (plate) to the lower left turn knob, lower the bucket (board) mechanism, release the knob to the middle, and then rotate the scraper operation knob to the right fold, fold the scraper, release the knob to the middle, ready to start hanging the bucket or bucket.

(2)Step 2. Hang the trash can, rotate the bucket operation knob to the right upper turn position, the trash can turn up, automatically discharge the garbage into the circular arc bucket 2, release the knob back to the middle, can also automatically operate.

(3)Step 3. Rotate the bucket knob to the lower left turn position, put the trash can back, release the knob back to the median; then rotate the slide knob to the left slide position, slide the slide (note: the scraper in the upward position), release the knob back to the median; Do not stand on the compressed garbage truck during the bucket or flip.

(4)Step 4. Rotate the scraper operation knob to the left scraping position, scrape up the garbage along the arc bucket body, and release the knob to return to the middle.

(5)Step 5. Rotate the skateboard operation knob to the right upper slider position (note: the cylinder seat under the scraper must exceed the marked position of the stroke switch), the skateboard drives the scraper to slide up at the same time, release the knob to return to the middle, the garbage is picked up by the scraper, ready to push the garbage.

(6)Step 6. Rotate the negative pressure operation knob to the right push position, the garbage is pushed into the car box by the negative pressure plate, and release the knob to return to the middle;

(7)Step 7. Rotate the negative pressure operation knob to the left recovery position, withdraw the negative pressure plate, release the knob to return to the middle, and complete the loading of garbage once;

If you load the garbage again, continue the cycle from step 1 (rotate the scraper operation knob to close, ready to start the bucket).

(8)Step 8. If it is not necessary to load again, rotate the bucket operation knob to the right upper turn position, turn the bucket mechanism, and then release the force collector, before the vehicle can move.

(9)Step 9. Turn the operation knob of the push board to the right push position, the push board in the box will push the garbage into the box, release the knob to complete the garbage discharge work; (pay attention to the maintenance of the oil cylinder, and make butter).

(10)Step 10. Rotate the push plate operation knob to the left recovery position, and the push plate is withdrawn, release the knob; then rotate the bucket operation knob to the left drop position. If the body is lowered and locked with the trunk, please turn up), and the vehicle can be moved.

(11)Warm tips: after a period of use, check whether the universal joint screws are loose and need to be tightened or replaced (the hydraulic pump and the transmission shaft is not within the chassis service range because of the upper part, the user needs to regularly check the fastening).

(12)Special personnel should be asked for commissioning; simulate various complex working environments and all compressed physical tests. After-sales guarantee; non-customer human damage, any fault unconditional after-sales, customer zero cost solution.

8.Company scale display (part) picture

9.Workshop process picture (part) display

10.Model user use function picture display

Frequently Asked Questions

1. Q: What is the main advantage of an 8-cubic-meter capacity for this truck?
A: The 8-cubic-meter capacity offers an optimal balance between maneuverability in narrow urban streets and substantial waste load per trip. Combined with high-powered compaction, it maximizes collection efficiency without compromising on agility.

2. Q: What types of waste can this truck handle effectively?
A: It is designed for mixed municipal solid waste (MSW), including bagged household waste, loose bulk trash, and light recyclables. Its robust compaction system is engineered to handle common urban waste streams efficiently. (Note: It is not suitable for construction debris, liquid waste, or hazardous materials).

3. Q: How does the compaction system work, and what is its ratio?
A: The truck features a hydraulically powered blade or panel that compresses waste inside the container. This significantly increases payload by reducing air space. A typical compaction ratio ranges from 3:1 to 5:1, meaning 24-40 cubic meters of loose waste can be compacted into the 8-cu.m container.

4. Q: What is the expected payload (weight capacity) after compaction?
A: The payload capacity depends on the truck chassis rating and legal Gross Vehicle Weight (GVW) limits. A standard model on a suitable chassis can typically carry 4,000 to 6,500 kg of compacted waste. Please consult specifications for the exact figure based on the chassis model.

5. Q: What safety features are included for operators?
A: Standard safety features include rear-view cameras, audible reverse alarms, emergency stop buttons, clearly marked danger zones, and interlock systems that prevent compaction cycle operation during certain functions to protect personnel.

6. Q: How reliable is this truck for daily, heavy-duty use?
A: Built with high-strength steel and durable hydraulic components, this truck is engineered for demanding municipal collection cycles. Key wear parts are easily accessible for maintenance, ensuring high uptime and a long service life with proper care.

7. Q: Is training provided for drivers and maintenance staff?
A: Yes. We provide comprehensive operational and basic maintenance training with each purchase. This ensures safe, efficient use and helps your team perform routine checks to minimize downtime.

8. Q: What kind of chassis is this body compatible with?
A: The compaction body is designed to be mounted on a standard commercial truck chassis from major manufacturers like Dongfeng, FAW, ISUZU, FOTON, etc., with appropriate wheelbase and weight ratings. We can assist in specifying or sourcing a compatible chassis.

9. Q: What are the key maintenance requirements and intervals?
A: Regular maintenance focuses on the hydraulic system (checking fluid levels, filters, hoses), greasing all moving joints, and inspecting the packing blade/carriage for wear. Daily visual checks and scheduled servicing (e.g., every 250-500 hours) are recommended for optimal performance.

10. Q: What is the warranty coverage for this vehicle?
A: We offer a standard warranty covering manufacturing defects on the compactor body and its key components (e.g., hydraulic cylinders, pump, control system) for a period of 12 months or a specified number of operational hours. The chassis warranty is provided separately by its manufacturer.